3dscapture.com

Support Forum
It is currently Thu Jul 27, 2017 4:31 am

All times are UTC




Post new topic Reply to topic  [ 328 posts ]  Go to page Previous  1 ... 21, 22, 23, 24, 25, 26, 27 ... 33  Next
Author Message
PostPosted: Wed Jan 21, 2015 7:21 pm 
Offline
Site Admin
User avatar

Joined: Wed Sep 19, 2012 7:44 pm
Posts: 1539
P1kas wrote:
I can do the installation myself, so long as it only requires soldering wires from the adapter board to the 3DS's board. Have a bit of electronics soldering experience so I should be fine.

All I'd need is a diagram or pictures of where to connect each point to. If you can somehow provide this I'd be happy to do this myself.

What would the package include? Board, cables and the little adapter 3 prong port? I'd have to mod the side of the 3DSs case for it to be like the one you showed, correct?

Thanks for any info!

Yes, I need to prepare photos, diagrams, wiring info. I was planning on selling just the board and connector, for about $15. Maybe I should offer extension cables as well? It does makes things a little more complicated, since it can work with 5 different types of controllers. This is very much a DIY product, that was my intent. Cables are hand-made. Lots of wires, soldering, case cutting and gluing involved.

Gummo should be offering installations soon, and my EU partner http://www.merki.net will also be getting some boards. I don't want to do installations myself yet, except maybe for some special circumstances. I stopped doing capture installations for a reason...

Image


Report this post
Top
 Profile  
Reply with quote  
PostPosted: Thu Jan 22, 2015 9:34 pm 
Offline

Joined: Thu Jan 15, 2015 3:58 am
Posts: 5
So am i hearing this straight, that we will not be able to purchase a board with both mods pre-installed?


Report this post
Top
 Profile  
Reply with quote  
PostPosted: Thu Jan 22, 2015 9:49 pm 
Offline
User avatar

Joined: Mon Jun 24, 2013 12:59 pm
Posts: 145
Location: Germany
In Europe I will offer this service soon!

You can choose:
- just the installation of the GCC-Mod in your 3DS
- both 3DS Capture Card with GCC-Mod in your 3DS
- preinstalled 3DS System with 3DS Capture Card with GCC-Mod

I have to see what is the demand here in Europe :)


Last edited by Tecd0c on Thu Jan 22, 2015 9:54 pm, edited 1 time in total.

Report this post
Top
 Profile  
Reply with quote  
PostPosted: Thu Jan 22, 2015 9:51 pm 
Offline

Joined: Thu Jan 15, 2015 3:58 am
Posts: 5
What about USA?


Report this post
Top
 Profile  
Reply with quote  
PostPosted: Fri Jan 23, 2015 4:55 pm 
Offline
Site Admin
User avatar

Joined: Wed Sep 19, 2012 7:44 pm
Posts: 1539
Drjack6 wrote:
So am i hearing this straight, that we will not be able to purchase a board with both mods pre-installed?

I don't HAVE capture boards to sell right now. Maybe when I do, I'll offer these.


Report this post
Top
 Profile  
Reply with quote  
PostPosted: Fri Jan 23, 2015 5:33 pm 
    loopy wrote:
    I was planning on selling just the board and connector, for about $15. Maybe I should offer extension cables as well? It does makes things a little more complicated, since it can work with 5 different types of controllers. This is very much a DIY product, that was my intent. Cables are hand-made. Lots of wires, soldering, case cutting and gluing involved.


    When I said cables, I meant the wiring used in the soldering process. However, now that you've mentioned the actual cables that connect to the port, I'd like at least one. It'd be the DS2 controller one; whenever I'd like to use any other controller I could simply buy an adapter and remap the controls accordingly, correct? A DS2 to GC, DS2 to SNES, etc..


    Report this post
    Top
      
    Reply with quote  
    PostPosted: Fri Jan 23, 2015 5:49 pm 
    Offline
    Site Admin
    User avatar

    Joined: Wed Sep 19, 2012 7:44 pm
    Posts: 1539
    Maybe an adapter would work, I don't know. I haven't tried.
    This is what I use -- just a plain extension cable with one of the ends replaced.

    Image


    Report this post
    Top
     Profile  
    Reply with quote  
    PostPosted: Fri Jan 23, 2015 7:49 pm 
    Loopy can you also port the cable connections of the ps2 adapter ?

    Want to solder them on my own. Thx !


    Report this post
    Top
      
    Reply with quote  
    PostPosted: Fri Jan 23, 2015 7:50 pm 
    Offline

    Joined: Mon Sep 29, 2014 7:32 pm
    Posts: 10
    Post, sorry wasn't logged in.

    The pin strip is 2,54mm ?


    Report this post
    Top
     Profile  
    Reply with quote  
    PostPosted: Fri Jan 23, 2015 10:12 pm 
    Loopy, when will these boards be available? Also, will you sell them via the 3dscapture.com order page?


    Report this post
    Top
      
    Reply with quote  
    Display posts from previous:  Sort by  
    Post new topic Reply to topic  [ 328 posts ]  Go to page Previous  1 ... 21, 22, 23, 24, 25, 26, 27 ... 33  Next

    All times are UTC


    Who is online

    Users browsing this forum: No registered users and 1 guest


    You cannot post new topics in this forum
    You can reply to topics in this forum
    You cannot edit your posts in this forum
    You cannot delete your posts in this forum
    You cannot post attachments in this forum

    Search for:
    Jump to:  
    Powered by phpBB® Forum Software © phpBB Group Color scheme by ColorizeIt!